Team 3D

From Leeds Hackspace Wiki
Revision as of 12:58, 15 January 2019 by BShute (talk | contribs) (Corrected indentation)
Jump to navigation Jump to search

This page is under construction. PLEASE STAND BY.

3D printer construction and maintanance team.

Proposals

This is a list of proposed suggestions, ideas, shenanagins, and other various odities that may be informative

These are all hypothetical conjecture, and may not be practically implementable.

Proposed projects

These are Projects; Itemised and contained, running for a hopefully finite span of time.

TODO

Proposed plans

These are more long form policies than individual projects.

Long term print corner operations

TODO

Once most of the 3d printers are working at all well, we will have many working printers

As it is unlikley that all of them will be utilised continuously, and hackspace space isn't exactly in surplus, all of the printers need to serve at least some basic continuous purpose

  • Prusa - Sitting and being awesome
  • Felix - Rapid prototyping (IIRC it canout-pace the prusa)
  • BigBox - MultiMat/Large form factor
  • MendelMax - Large form factor + Prototyping (See Below TODO)


Procedures

These are standard procedures needed for printer setup/configuration

PLEASE: Check with a print maintainer before you mess with the printers. We like not returning to a tangled mess of broken printers and dreams.

PID Tuning

This is used to stop the fracking printers from fracking failing to fracking heat up.

MOST 3D printers use PID loops to maintain the hotend and bed temperature. PID loops are used to account for the slew that is heat transfer. If they don't they will laugh at you when you try to mess with PID.

AutoTune

Marlin and The RepRap wiki have some great docs on how to autotune PID.

To summarise so you don't need to read them you GENERALLY call:

M303 C<count> E<tool> S<temp> U1

For this command:

  • The count is how many loops of pid tuning to run
  • The tool is what you are tuning; Extruder number indexed from zero, OR -1 for bed
  • The temp is the temp to calibrate at. I.e. if you are having stabiluity issues at 220C, then you want S220
  • The U1 tells the printer to use this value instead of just printing it to console.

You then save with:

M500

If you have EEPROM enabled. Which you should


Pro-Tip: If your temperature plummets when the fans come on, enable the fans before performing a PID tune

Manual Tune

When autotune fails, manually tuning CAN work.

There are 3 pid values each meaning different things:

  • The proportional factor - P - How much PID cares about the difference between target and current
  • The integral factor - I - How much PID cares about the historical difference from the target
  • The derivative factor - D - How much PID cares about the rate of aproach to the target

Some common problems solvable by this:

  • Printer never reaches tempreture - Increase P
  • Printer overshoots - Decrease P AND/OR Increase D
  • TODO: MORE

Calibration Dump

The current printer calibration data can be dumped using an M503 command

This can then be copied to the wiki in a code block, such that any maintainer can access the wiki to restore the calibration, even if the one who calibrated it is no longer there.

TODO: MORE

Unblocking Hotend

Most of this guide section is built for E3D hotends. Most of our printers run them. As always: If unsure check with someone.

These assume the nozzle isn't blocked. TODO FIXME

Heat killable blockage

Take this to be phase 1 of the process of killing blockages.

The procedure here is simple:

  • Heat up printer above normal print temp. Prusa recomend 250 for PLA; 270 for ABS
  • Feed filament in (if necesary, with "encouragement")
  • Hope it extrudes

If it does WOOT. If not: Try a higher temp or onto:

Hard blockages

So trying to melt out the blocky git has failed. Now you need to push it out. This generally means the blockage is higher up in the heatbreak; likley in the heatsink side.

To do this you need:

  • Your hotend extracated from the printer head (with nozzle removed)
  • A long, rigid stick like implement for pushing the blockage out (should be slightly less than the diameter of the filament)

If you are going the full hog and getting out the heatbreak; an 1.5mm allen key may work.

Procedure:

  • Push tool down hotend
  • Try both ends

If this fails cold:

This may need lots of heat. I.e. >300C; Instant burning, hand melting temps. Beware.

  • If still attached to the printer (heat cartridge+thermistor) try heating it up and repeating
  • If it is not attempt to extracate the heatbreak and push it out of that; while heating it up with a hot air gun
  • If the heatbreak is stuck in the Radiator, remove the PTFE liner, then heat with a blow torch.
    • If you cannot remove the liner then HARD ABORT; PTFE is dangerous if heated above 250C (hence why it doesn't go into the heat block)